The article author is making a few good points on Tools You Need to Install a New Bathtub overall in this article directly below.
Mounting a bathtub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old tub with a new one is also a moderately difficult project. If the old tub is conveniently accessible, the project can move rapidly; if you have to open a wall surface to remove the old tub and position the new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old tub as well as set in the brand-new one. Ensure you have certified on your own for the work as well as are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed job, it is much better to think about utilizing one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly aid you set up a brand-new bathtub in your bathroom if you have currently purchased a brand-new tub and also do not require to change the plan of your previous supply of water pipelines.
Your tools and also product list ought to make up the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bath needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be quite troublesome due to the restricted gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before moving on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, position the bath tub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub till the spirit level reads level.
To mount taps, fit all-time low of the outermost flexible faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Turn on the water system as well as check all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bath tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, repair the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the bathtub needs to wait up until the bath tub has actually been made use of at least once as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Secure the tap in place with the supplier provided backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The former type should be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack a stiff seal, triggering the water to pass through the wall in between the bathroom and the tiling, causing difficulties with dampness as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can split fairly early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that page on Installing A Bathtub when doing a search on the internet. For those who liked our page please do not forget to share it. Thank you so much for your time invested reading it.
Leaks? Ring us!